Boral Driveway & Pavers Nationwide

Boral Driveway & Pavers: The Cupertino Owner’s Guide

Boral driveway and paver repair in Cupertino typically runs $5,000-$14,000 for full replacement, while targeted paver resets or base repairs start around $800-$2,500. We stock Boral-compatible pavers and base materials for same-day starts on most repairs. Most Cupertino owners notice the problem after winter rains: water pooling where it didn’t before, or individual pavers rocking underfoot where the bedding sand has washed out from beneath the Boral unit.

Call (669) 202-9618

Which Boral Models This Applies To

Boral’s hardscape line changed hands in 2021 when Westlake Royal Building Products acquired the division, so identifying your exact series matters for color match and joint spacing. The common Cupertino installs we see are Boral Stonegate (the tumbled concrete paver, 60mm thickness, usually laid in running bond), Boral Plaza (the larger format, 80mm, common in Monta Vista driveways from the 2015-2019 build wave), and the older Boral Cobble series (pre-2016, often found in Ranchlands and the older Fairgrove sections). Check the paver edge: Stonegate has a chamfered edge with “Boral” stamped on the spacer nub; Plaza has a clean arris and a part number etched on the bedding face. If you’re trying to patch rather than replace the whole field, bring a sample to our office. Boral’s color lots shift with aggregate source, and the “Slate” you bought in 2017 is not the “Slate” in current stock. We maintain a cross-reference to the closest Westlake Royal match, and we can source reclaimed lots through our distributor network when the color match needs to be exact.

Signs Your Boral Driveway & Pavers Is Failing

• Individual pavers rock or sink when stepped on. This means the bedding sand layer has eroded or the base aggregate has settled, usually from water intrusion through failed edge restraints. In Cupertino’s clay-heavy soils, especially around the Permanente Creek drainage, this happens faster than the manufacturer specs suggest.
• Weeds growing thick through the joints. The polymeric sand has degraded or was never properly compacted. On south-facing Boral installs in Cupertino, UV exposure breaks down the sand binder in 3-5 years, not the 7-10 you’d expect in milder climates.
• Efflorescence that returns after cleaning. White chalky deposits mean moisture is moving through the paver body from below, often from a base that wasn’t graded for drainage. Boral’s concrete pavers are porous; the issue is almost always the substrate, not the unit itself.
• Edge pavers tilting outward or separating from the field. The plastic or concrete edge restraint has cracked or pulled its spikes. This is the failure we see most often on Boral Plaza installs in Cupertino, where the 80mm thickness creates more lateral thrust against the restraint.
• Surface spalling or corner breakage. De-icing salt use, pressure washer damage, or freeze-thaw in shaded areas. Boral’s 2016-2019 production run had a known issue with surface durability in high-sulfate soils; we’ve documented this in several Cupertino properties near the Stevens Creek corridor.

Before

After

Replacement Cost & What’s Included

For Boral paver work in Cupertino, here’s how the numbers break down:

The spread depends on three things: how much base needs to be excavated and recompacted, whether we can match your existing Boral color lot or you’re choosing new, and the access (steep driveways in the Cupertino Hills add labor hours). Every quote is a flat written price with line-item breakdown: demolition, base prep (class II aggregate, compacted in lifts), bedding sand, paver installation, joint sand, and edge restraint. Under Clause 1 of the Haven Standard, that price is locked before we start. No change order moves without your signature. Our paver work carries a 365-Day Done Right Promise: if the base settles or joints open, we return and make it right.

DIY or Call Us?

There’s honest work a homeowner can do: pull a few pavers, check if the bedding sand is still graded, look for standing water in the base. But the reset itself is where DIY goes wrong. Boral pavers require a plate compactor for both base and final compaction; hand-tamping leaves voids that become rockers in six months. The polymeric sand needs to be swept, vibrated, and wetted in a specific sequence or it bonds unevenly. And if your edge restraint has failed, the fix involves excavation, new spike placement, and geotextile work that most homeowners don’t have the tools for. We’re not going to tell you it’s dangerous like electrical work, but we will tell you that half the Boral repairs we do in Cupertino are fixing a DIY reset that lasted one season. Call (669) 202-9618 and we’ll give you a written price for the proper fix.

FAQs